- #How to connect to a mikrotik router with winbox 3.11 portable
- #How to connect to a mikrotik router with winbox 3.11 windows
Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled io scheduler deadline registered (default) jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. squashfs: version 4.0 (1) Phillip Lougher workingset: timestamp_bits=30 max_order=14 bucket_order=0 Crashlog allocated RAM at address 0x3f00000 UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) UDP hash table entries: 256 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) clocksource: Switched to clocksource MIPS MIPS: machine is MikroTik RouterBOARD 750 r2 futex hash table entries: 256 (order: -1, 3072 bytes) clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) sched_clock: 32 bits at 425MHz, resolution 2ns, wraps every 5052902398ns clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4497083404 ns SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) PID hash table entries: 256 (order: -2, 1024 bytes) Built 1 zonelists in Zone order, mobility grouping on. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Initrd not found or empty - disabling initrd SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
#How to connect to a mikrotik router with winbox 3.11 windows
Set a static IP on your Windows computer LAN port with the followingġ92.168.1.2 (Keep this to 192.168.1.2 or tftpd wont work **IMPORTANT**)įollow method 1 to enable TFTP, Once done keep the LAN on port 1 (interent port) and then you should see something transferring and then the RB750r2 will boot into LEDE, Unplug the LAN port from Internet port 1 and set a DHCP on your Windows machine and then plugin the LAN port into any port 2-5 and the Internet port for a Cable Modem? Switch? Router? something that has internet access to it if you want to keep the LEDE on as this is in RAM mode and wont save any changes! Open up tftpd64.exe and the go to Settings > GLOBEL and make sure, TFTP server and DHCP are ticked, everything else untick, Save and Exit and then reopen tftpd64.exe for the saved changes!
#How to connect to a mikrotik router with winbox 3.11 portable
LEDE Stable 17.01.1 () LANs are NOT WORKING again only the snapshot builds are working with LEDE!įor Windows 7 SP1 圆4 (XP/Vista should be ok)ĭownload (i used tftpd64 portable edition) and the mikrotik-rb-nor-flash-16M-initramfs-kernel.bin and mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin from Downloads above and then save them in the same tftpd32 folder IMPORTANTĮxtract the tftpd32 folder and make sure mikrotik-rb-nor-flash-16M-initramfs-kernel.bin is there and open up tftp32 config file and match theses settings i have (worked for me)ĤC:5E:0C:XX:XX:XX=192.168.1.250 (Should be the same ETH1 MAC Address)īootFile=lede-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin Note for LEDE Development version, Yes is working as of r4049-9412fc2 but may contain bugs! No LuCI/Web interface is included so please wait for LEDE or OpenWrt newer release if you need this Stable! LEDE Development Version, flash-16M-squashfs-sysupgrade.bin LEDE Development Version, Working, Port 1 WAN, 2-5 port LAN, All Working OpenWrt Trunk/Snapshot builds mikrotik-vmlinux-initramfs.elf
0 kommentar(er)
